The Code of Federal Regulations of the United States of AmericaU.S. Government Printing Office, 1951 The Code of federal regulations is the codification of the general and permanent rules published in the Federal register by the executive departments and agencies of the federal government. |
µµ¼ º»¹®¿¡¼
215 ÆäÀÌÁö
... Nothing contained in this section shall be so construed as to prevent the use of cleats or other retaining means for the purpose of preventing shifting of con- tainers or batteries . For the purposes of this section a false floor or ...
... Nothing contained in this section shall be so construed as to prevent the use of cleats or other retaining means for the purpose of preventing shifting of con- tainers or batteries . For the purposes of this section a false floor or ...
±âŸ ÃâÆǺ» - ¸ðµÎ º¸±â
ÀÚÁÖ ³ª¿À´Â ´Ü¾î ¹× ±¸¹®
acid apply approved attached Authorized gross weight barrels or drums blasting caps bottom brazing Bureau of Explosives calking carboys cargo tank carrier chapter cleats closure comply containers as follows corrugated fiberboard cylinders dangerous articles diethylene glycol dinitrate discharge exceed exemption expansion dome figures at least flammable liquids flange gases heat heater systems hydrostatic test Inches Inches Inches inside containers joint label lading leakage less letters and figures loaded manhole cover material ments Minimum thickness nitroglycerin package packed in specification percent placards plate plug poisonous pounds per square prescribed in paragraph projectiles rail express rated capacity retested rivets rolling hoops safety valves safety vent sealing device seams securely shipments side smokeless powder Spec specification containers specimen square inch steel stenciled tainers tank bands tank cars tank motor vehicles tank shell tare weight test pressure threads tion trichlorosilane welded Wooden boxes yield strength
Àαâ Àο뱸
157 ÆäÀÌÁö - The package must contain not more than 0.1 millicuries of radium, or polonium, or that amount of strontium 89, strontium 90, or barium 140 which disintegrates at a rate of more than 5 million atoms per second...
173 ÆäÀÌÁö - Nitric acid, when loaded with other acids or other corrosive liquids in carboys, must be separated from the other carboys. A 2 by 6 inch plank, set on edge, should be nailed across the car floor at least 12 inches from the nitric acid carboys and the space between the plank and the carboys of nitric acid should be filled with sand, sifted ashes, or other incombustible absorbent material.
182 ÆäÀÌÁö - STOP" being in letters at least 4 inches high and the other words in letters at least 2 inches high. The letters must be white on a blue background.
126 ÆäÀÌÁö - All liquefied petroleum gas in a tank motor vehicle shall be effectively odorized by an approved agent of such character as to indicate positively, by a distinctive odor, the presence of gas down to a concentration in air of not over one-fifth the lower limit of combustibility: Provided, however, That odorization is not required if harmful in the use or further processing...
50 ÆäÀÌÁö - Parts 71-78 of this chapter an explosive is defined as any chemical compound, mixture, or device, the primary or common purpose of which is to function by explosion, ie, with substantially instantaneous release of gas and heat, unless such compound, mixture, or device is otherwise specifically classified in Parts 71-78 of this chapter.
206 ÆäÀÌÁö - Yellow m" labels, (III) Class A or B poisons, or (iv) Hazardous materials In a portable tank or a DOT specification 106A or 110A tank. (d) [Reserved] (e) No sharp projections inside body of vehicles. No motor vehicle transporting any kind of explosive shall have on the interior of the body in which the explosives are contained, any inwardly projecting bolts, screws, nails, or other inwardly projecting parts likely to produce damage to any package or container of explosives during the loading or unloading...
246 ÆäÀÌÁö - For lots of 30 or less physical and flattening tests are authorized to be made on a ring at least 8 Inches long cut from each cylinder and subjected to same heat treatment as the finished cylinder.