The Code of Federal Regulations of the United States of AmericaU.S. Government Printing Office, 1949 The Code of federal regulations is the codification of the general and permanent rules published in the Federal register by the executive departments and agencies of the federal government. |
도서 본문에서
100개의 결과 중 1 - 5개
7 페이지
... Steel Bars and Shapes , American Society of Mechanical Engineers , New York , N. Y. Irregular . See 46 CFR 51.10 . Standard Specifications for Carbon - Steel Bolting Material , Manufacturers ' Standardization Society of the Valves and ...
... Steel Bars and Shapes , American Society of Mechanical Engineers , New York , N. Y. Irregular . See 46 CFR 51.10 . Standard Specifications for Carbon - Steel Bolting Material , Manufacturers ' Standardization Society of the Valves and ...
156 페이지
... steel is less than No. 16 B. W. G. the elongation shall be not less than 15 percent in a gage length of 8 inches . ( b ) The bottom shell plating shall be increased to gages as shown in table for not less than 25 percent of the breadth ...
... steel is less than No. 16 B. W. G. the elongation shall be not less than 15 percent in a gage length of 8 inches . ( b ) The bottom shell plating shall be increased to gages as shown in table for not less than 25 percent of the breadth ...
158 페이지
... Steel gunwales made from steel plates bent to a 1⁄2 inch inside radius need not be fitted with nosings . The vertical leg of the gunwale shall be out- board of the sheer strake . [ Order 138 , 6 F. R. 4260 ] § 37.2-12 Gunwale braces ...
... Steel gunwales made from steel plates bent to a 1⁄2 inch inside radius need not be fitted with nosings . The vertical leg of the gunwale shall be out- board of the sheer strake . [ Order 138 , 6 F. R. 4260 ] § 37.2-12 Gunwale braces ...
185 페이지
... steel at least one- half inch thick , and are to have a width of bearing surface of at least 3 inches . § 43.13 ... steel casings of ample strength , and where the casings are not protected by other structures their strength is to be ...
... steel at least one- half inch thick , and are to have a width of bearing surface of at least 3 inches . § 43.13 ... steel casings of ample strength , and where the casings are not protected by other structures their strength is to be ...
186 페이지
... steel , of substantial con- struction , with screw or bayonet joints . Where a scuttle is not secured by hinges , a permanent chain attachment is to be provided . The position of flush bunker scuttles in small vessels in special trades ...
... steel , of substantial con- struction , with screw or bayonet joints . Where a scuttle is not secured by hinges , a permanent chain attachment is to be provided . The position of flush bunker scuttles in small vessels in special trades ...
기타 출판본 - 모두 보기
자주 나오는 단어 및 구문
amended apparatus appliances applicant barges bilge boat boiler bolts bulkhead capacity cargo carried certificate CGFR chapter Coast Guard District coastwise compartment construction crew davits deck department engine equipment examination exceed feet fire extinguishers fitted flange freeboard freeboard deck fusible plugs gas welding grade gross tons Guard District Commander gunwale hydrostatic hydrostatic test identical inspec inspector installed joints Lakes least length less license lifeboats load line located Marine Inspection master material maximum ment merchant mariner's document metal minimum motor vessels navigation Officer in Charge openings operated passenger vessels percent person pipe plate plugs port pounds per square pressure vessels pumps rafts regulations riveted rowlocks safety valve sels shell side specified square inch Stat steam or motor steam vessels steamers steel subchapter Subpart superstructure tank ships tank vessels TB/ALL tensile strength test specimen thickness tion tubes U. S. Coast Guard voyage watertight welded
인기 인용구
77 페이지 - A combined lantern in the fore part of the vessel and lower than the white light aft, showing green to starboard and red to port, so fixed as to throw the light from right ahead to two points abaft the beam on their respective sides.
77 페이지 - On the port side a red light so constructed as to show an unbroken light over an arc of the horizon of 10 points of the compass, so fixed as to throw the light from right ahead to 2 points abaft the beam on the port side, and of such a character as to be visible at a distance of at least 2 miles.
263 페이지 - This analysis shall be made from a test ingot taken during the pouring of the melt. The chemical composition thus determined shall be reported to the purchaser or his representative, and shall conform to the requirements specified in section 2.
275 페이지 - Wrought Iron. — A ferrous material, aggregated from a solidifying mass of pasty particles of highly refined metallic iron with which, without subsequent fusion, is incorporated a minutely and uniformly distributed quantity of slag.
69 페이지 - Commerce that he has been trained in all the operations connected with launching lifeboats and the use of oars; that he is acquainted with the practical handling of the boats themselves; and, further, that he is capable of understanding and answering the orders relative to lifeboat service.
639 페이지 - ... address of the witness, the matters concerning which it is expected the witness will testify, and the time and place proposed for the taking of the deposition, together with the name and address of the person before whom it is desired that the deposition be taken...
246 페이지 - ... the whole volume of the main compartment will not be flooded, a proportionate allowance may be made in the permissible length otherwise required for such compartment. In such a case the volume of effective buoyancy assumed on the undamaged side shall not be greater than that assumed on the damaged side.
278 페이지 - ... rolled. (b) If any test specimen shows defective machining or develops flaws, it may be discarded and another specimen substituted. (c) If the percentage of elongation of any tension test specimen is less than that specified in Section...
78 페이지 - ... points abaft the beam on the port side. The said side lights shall be fitted with inboard screens of sufficient height so set as to prevent these lights from being seen across the bow.
246 페이지 - A main transverse bulkhead may be recessed provided that all parts of the recess lie inboard of vertical surfaces on both sides of the ship, situated at a distance from the shell plating equal to onefifth the breadth of the ship...