The Code of Federal Regulations of the United States of AmericaU.S. Government Printing Office, 1957 The Code of Federal Regulations is the codification of the general and permanent rules published in the Federal Register by the executive departments and agencies of the Federal Government. |
도서 본문에서
100개의 결과 중 1 - 5개
296 페이지
... thickness , firmly glued together with waterproof glue ( a section of ply- wood from body shell is immersed in water at room temperature for 48 hours . If no delamination or separation of plys is apparent , the glue is deemed to be ...
... thickness , firmly glued together with waterproof glue ( a section of ply- wood from body shell is immersed in water at room temperature for 48 hours . If no delamination or separation of plys is apparent , the glue is deemed to be ...
300 페이지
... thickness by 21⁄2 inches width up to 62 gallons and 10 inch thickness by 3 inches width up to 13 gallons . The grain of alternate plies shall be at right angles . Hoops shall butt or slightly gap and shall be fastened to the body sec ...
... thickness by 21⁄2 inches width up to 62 gallons and 10 inch thickness by 3 inches width up to 13 gallons . The grain of alternate plies shall be at right angles . Hoops shall butt or slightly gap and shall be fastened to the body sec ...
351 페이지
... thickness of shell metal . ( 2 ) Longitudinal seams in shells : By forged lap welding , by copper brazing , by copper alloy brazing , or by silver alloy brazing . Copper alloy composition must be : Copper , 95 percent minimum ; Sili ...
... thickness of shell metal . ( 2 ) Longitudinal seams in shells : By forged lap welding , by copper brazing , by copper alloy brazing , or by silver alloy brazing . Copper alloy composition must be : Copper , 95 percent minimum ; Sili ...
355 페이지
... thickness of heads and bot- toms shall be not less than 90 percent of the required thickness of the side wall . ( b ) Circumferential seams . By weld- ing or by brazing . Heads attached by brazing must have a driving fit with the shell ...
... thickness of heads and bot- toms shall be not less than 90 percent of the required thickness of the side wall . ( b ) Circumferential seams . By weld- ing or by brazing . Heads attached by brazing must have a driving fit with the shell ...
356 페이지
... thickness shall be 0.078 " . In any case the minimum wall thickness shall be such that the calculated wall stress at minimum test pressure ( § 78.51-14 ) shall not exceed the lesser value of any of the following : ( 1 ) The value shown ...
... thickness shall be 0.078 " . In any case the minimum wall thickness shall be such that the calculated wall stress at minimum test pressure ( § 78.51-14 ) shall not exceed the lesser value of any of the following : ( 1 ) The value shown ...
기타 출판본 - 모두 보기
자주 나오는 단어 및 구문
acid amended by Order approved attached Authorized gross weight barrels or drums blasting caps bottom brazing Bureau of Explosives carboys carrier certify chap chapter cleats closed closure comply containers as follows corrugated fiberboard cushioned cylinders dangerous articles devices Dichlorodifluoromethane dome exceed exemption fiberboard boxes flammable flange gallons capacity gauge length head heat hydrostatic test Inches Inches Inches inside containers label leakage less liquefied petroleum gas liquid loaded manway mark specified material ments Metal barrels minimum thickness motor vehicle nails nitroglycerin Order 27 package packed in specification paragraph percent placards plate plosives plug Poison pounds per square prescribed projectiles rail express rated capacity retested riveted Rolling hoops sealing device seams securely sheets shell shipments shipped side solid Spec specification containers specimen square inch steel tainers tank cars tare weight tensile strength test pressure threads tion trichlorosilane vent welded Wooden boxes yield strength
인기 인용구
372 페이지 - When the average value of the three specimens equals or exceeds the minimum value permitted for a single specimen and the value for more than one specimen is below the required average value, or when the value for one specimen is below the minimum value permitted for a single specimen, a retest of three additional specimens shall be made. The value of each of these retest specimens shall equal or exceed the required average value. When an erratic result is caused by a defective specimen, or there...